Good Morning Paints Private Limited

IPNet System Interpenetrating Polymer Network Concrete Coating System Interpenetrating Polymer Network Coating System is a novel type of polymer formulation consisting of more than two polymers cross linked in the network form by synthesis.

KARAIKOTE 4 Coat System CECRI Approved
Concrete and Steel Coating System against Corrosion, Carbonation & Weathering Effects
Karaikote® is an integrated coating system forprotection of RCC and Steel structures againstcorrosion and weathering effects.Karaikote® is an anti-corrosive coating systemcomprising of -• Primer coat (epoxy based)• Middle coat (epoxy based)• Top coat (epoxy based)• Finish coat (aliphatic polyurethane based)TYPICAL APPLICATIONSProtective coating to Bridge Decks, PSC BoxGirders, Soffits, Pile Caps, Pier Heads, Culverts,Sewerage Treatment Plants, Jetties, MarineStructures, Fertilizer Silos, Sheds and UreaBagging Plants, Water Treatment Plants, IndustrialStructures, etc.APPLICATION PROCEDUREThoroughly clean the surface by mechanicalmeans or by sweep sand blasting to removeresidual dust, oil and depositions. Prior toKaraikote® Primer application, seal all the cracks,crevices, surface blemishes with sealant PCSealant.Mix the Part A and Part B in specified proportionsand apply by brush or spray leaving 24 hoursinterval between the coats. Apply the subsequentcoats of Karaikote® Middle coat, Karaikote® Topcoat & Karaikote® Finish coat.

EPIBOND-11 Multifunctional Versatile Epoxy System
EPIBOND 11 is a multifunctional versatile epoxy system which can be used effectively for belowapplication:TYPICAL APPLICATIONS• As a bonding coat between old to new concrete.• For preparing high strength epoxy mortar.• As an anti-corrosive coating to structural steel.• As a protective coating to internal areas of water retaining structure.• As a epoxy grouts for sealing of cracks, honeycombs and strengthening concrete matrix.

IPNet System Interpenetrating Polymer Network Concrete Coating System
Interpenetrating Polymer Network Coating System is a novel type of polymer formulation consisting of morethan two polymers cross linked in the network form by synthesis. The morphology studies conducted atCBRI, Roorkee using Scanning Electron Microscopy & Differential Scanning Calorimetry have proved theefficacy of IPNet® systems with respect to Chemical Resistance, Weather Resistance, Tensile Strength,Flexibility, Shear Strength & Hardness Properties.

GOLDBOND 1893 - PRIMER PART-A

GOLDBOND 1893 SATURANT PART-A

IPNET RB iiiiiiii

GOLDBOND 1893 PRIMER & SATURANT
poxy Primer & Saturant System for E-Glass / Carbon Fibre Applications On Concrete GOLDBOND^®1893 is a 2 part specialty system comprising of a primer part and a saturant part. GOLDBOND^®1893 Primer is comprised of a base and curing agent. GOLDBOND^®1893 Saturant is also comprised of a base and curing agent.

Waterseal® is a unique formulation that providespositive waterproofing to the structure.Waterseal® is a chemically cured epoxy stearatecompound of base and curing agent to be mixed inequal proportion by volume prior to theapplication.

STELLYNCrystalline Integral Waterproofing Admixture Unlike any other organic admixture STELLYN is a hydraulic waterproofing compound and being inorganic fully compatible with cementitious materials The cementitious matrix has lot of capillary voids in concrete. These are responsible for leakage as well as deterioration at a later stage once the water pressure in the capillaries build up The inorganic chemical group in water STELLYN will react with water and insoluble crystalline products are generated throughout the capillary pores of concrete This crystalline product is highly resistant to water and perform very well even under extreme conditions such as pressure or aggressive chemicals attack Application:

• STELLYN can be added to into concrete either in batching plant or mixing trucks as per the dosage by consultant
• It is recommended that STELLYN is added into batching plants lastly into concrete and through mixing for 5 to 10 minutes is envisaged
• The amount of water to be determined only after carrying out mix since STELLYN also has water reduction property along with crystallisation
• Water is an important agent to form crystalline process. Initially water will access to concrete through porous portion of concrete. STELLYN will then react with water and crystallisation process initiates 

POWRTHROWSustained Release Caplet for Corrosion Protection of Existing RCC Structures The reduction of service life of any RCC structure is basically due to corrosion of rebar. This process is very severe when structures are exposed to marine or chemical atmosphere. Powrthrow is an unique solution for maintaining the integrity of existing RCC structure from corrosion of rebar. By introducing Powrthrow into the concrete structures, the rate of corrosion of rebar reduces significantly & the release of active ingredient is over a considerable period of time. METHOD OF APPLICATION

• Drill 20mm holes into the concrete to a depth of 25mm and insert the Powrthrow caplets into it. Seal it off with EPCO^®-1010
• Spacing of Powrthrow caplets can be,
  For Columns - 1 unit per RMT from 2 opposite faces in staggered fashion
  For Beams - 1 unit RMT from 2 opposite faces in staggered fashion
  For Slabs - ln 1mt x 1mt grid insert 4 units
• Seal it off with EPCO^® -1010

Note: For site specific applications the spacing can be designed separately  

Monopol 456 S
Silane Siloxane Penetrative Primer for Concrete and Masonry Monopol^®-456-S consists of reactive hydrophobic silane-siloxane with a very high degree of penetrative action. It works by penetrating into the pores of concrete and reacting with the existing water vapour to form hydrophobic polysiloxane lining to the pore capillaries. Application Procedure

• Thoroughly clean the substrate with the coarse wire brushes and wipe the dust, cementatious incrustation etc with a clean cloth or compressed air. Remove curing compound grease etc using clean water and detergents
• Apply by brush or spray
• Avoid application during high winds and hot hours especially in summers
• Subsequent coating can be applied immediately
• Keep the container away from direct heat or sunlight

CORROSEALCORROSEAL is a two pack polyamide cured air drying epoxy compound. CORROSEAL has excellent resistance to corrosion. Application Procedure

• Mix CORROSEAL Base & Curing agent in prescribed proportion by volume and allow it to remain for 10 minutes before application. Apply 2-3 coats of Corroseal with a time interval of 24 hours between coats

MONOPOL 160High Molecular Weight Polymer / Mortar MONOPOL^®-160 is a low viscosity high molecular weight thermosett polymer. Due to its low viscosity, cracks and honeycombs are filled upto full depth of concrete RCC / concrete roads. Application Procedure

• Surface preparation is an essential part of the application. It is necessary to clean and dry the concrete surface prior to use
• The concrete cracks or honeycombed surfaces shall be chipped to a minimum depth of 10mm in right angle to surface or as per requirement. The areas to be repaired shall be profiled to get rectangular or square shape with a right angle edge of 10mm
• Refer Technical datasheet for mixing
• Use it for gravity pouring / flooding within scheduled pot life
• Curing in air for 3-6 hours before allowing traffic to pass
• Follow stitching, stapling or grouting procedure whenever needed
• Repeat the same procedure for pot hole filling in concrete pavements, culverts and bridges and for levelling the surface as a wearing coat

EL-MONOBOND Two Component Non- Emulsiable Epoxy Latex System
EL-MONOBOND Two Component Non- Emulsiable Epoxy Latex System jhjhsdjdjsdk

Plastogrip Waterproofing Membrane is APP(Atactic Polypropylene) High performance polymer modified bituminous waterproofing membrane; Reinforced with

EPCO®-2020-TX Anti-Corrosive, Chemically resistant coal tar extended epoxy coating (EPRB) System for below & above waterline application
PROPERTIESExcellent adhesion, Excellent chemical resistance.Excellent resistance against chlorides, sulphatesand subsoil contaminants.

FEOVERT is a single pack alkaline waterbased rust converting primer which is designed for application on rusted embedded reinforcement to form a complex iron ...

Monopol®-456 is a concrete specific coatingsystem that provides protection against chlorideion penetration, carbonation, UV radiations andweathering effects.Monopol®-456 has excellent crack bridgingability and excellent biological resistance.TYPICAL APPLICATIONSFor coating Bridge Decks, PSC Box Girders,Cooling Towers, Chimneys, Pier Columns,Marine Structures, Viaducts, Aqueducts, Waterretaining structures, External surfaces ofE.S.R/M.B.R., Structures exposed to thermalstresses, Airline Hangars, Multi-storied buildings,etc.

As Waterproof, Water Resistant Anti- Carbonation Coating over Concrete. Ideal for Coating and Crack Filling of Concrete. Surfaces Like Terraces, Roofs,

EPMORT-350 Ready to use epoxy mortar system
EPMORT-350 is a two component prefilledepoxy mortar system comprising ofa resin component (Part A) and a hardnercomponent (Part B)

GOLDBOND 1893 SUPERWRAP 
E-glass fiber wrap for structural strengthening

Zerokorr Self-Healing, Anti-Corrosive Coating System for Structural Steel
Zerokorr is a specialized environment friendly polymers based system which passivates the pin holes,scratches and dents by redox mechanism. This improves durability and reduces maintenance cost of steelstructures since this coating is the first pinhole free barrier against different attacks in varied exposureconditions.TYPICAL APPLICATIONSAll Structural Steels, Steel chimneys, conveyors, Steel bridges, Trusses, workshops, pipelines, all structuralsteel members, etc.APPLICATION PROCEDURESurface Preparation: The steel substrate to be coated shall be blast cleaned using copper slag blasting toachieve SA 2 ½ grade to achieve near white metal. If blasting is not feasible use EPCO Prietch to clean therust scales.
Application:• Mix the Part A and Part B of Zerokorr Primer in prescribed proportion by volume thoroughly for 5-10minutes in a clean container (free from oily residues) and allow it to remains for 10-15 minutes.• Primer coat shall be applied on cleaned surface after surface preparation and within pot life.• After air curing as specified one coat of Zerokorr Interprimer, Zerokorr top coat, Zerokorr finish coatshall be applied keeping time interlag as specified.• The coating shall be applied by brush or airless spray. The intercoat interval shall be 24 hours.

MAKE- KRISHNA CONCHEM PRODUCTS PVT. LTD.
ZEROKORR PRIMER RS.489/Per Ltr+GST (10 Ltr Pack Size Set)
ZEROKORR INTERPRIMER RS.507/Per Ltr+GST (10 Ltr Pack Size Set)
ZEROKORR TOPCOAT RS.525/Per Ltr+GST (10 Ltr Pack Size Set)
ZEROKORR FINISH COAT RS.555/Per Ltr+GST (10 Ltr Pack Size Set)
THINNER T50 RS.230/Per Ltr+GST
Note :1) GST : GST @ 18% Applicable2) Payment Terms : 100% Advance3) Transportation: Frieght Charges Applicable4) Pack Size: All Products are available in 10 Ltr Set only.5) Availability: Available 7-10 Days6) Delivery  Period: P.O. against and payment against Available quantity within 07-10 Working Days.

EPCO KP-200 Bipolar Concrete Penetrating Corrosion Inhibiting Admixture (CPCIA)®
EPCO®-KP-200 is a hi-tech corrosion inhibitorsystem that works on the Bipolar InhibitionMechanism (B. I. M.)®. B. I. M.® inhibitscorrosion of steel in concrete at both the poles,cathodic & anodic simultaneously.EPCO®-KP-200 by virtue of its high vapourpressure & affinity for the embedded metaldiffuses through densest concrete to reach thecorroding steel. The migration of EPCO®-KP-200takes place over a prolonged period of time andhence this molecular layer shall continue toprotect rebar by its constant presence.

Monobond® is a polymer latex additive formodifying cement concrete / mortar / plaster /grouts. The addition of Monobond® improvesmechanical properties especially flexure andtension. Due to low permeability of polymermodifiedsystems, remarkable improvement inprevention of carbonation, chloride ionpenetration is observed. Also chemical resistanceimproves significantly.The addition of Monobond® imparts resilience tothe cement matrix. Thereby improving impactresistance. Also the modified cement matrix curesin air, eliminating the necessity of wet curing.It is necessary to mix Monobond® in water firstprior to addition in cement mortar/concrete

EL–Monobond®
is a two component non re- emulsifiable epoxy latex system which can be used for plain and cement modified coating applications over concrete/plastered substrates.                       

KARAIKOTE®–6545 is a uniquely formulatedhigh performance coating material recommendedfor applications on moist and dry surfaces ofconcrete and steel. KARAIKOTE®-6545 ismanufactured under technical know-how fromCentral Electrochemical Research Institute,Karaikudi.

Molith®PMM is a ready to use single componentcementitious polymer modified mortar for repairingconcrete structures.APPLICATIONIn damaged concrete structures Molith®PMM can beused to make up for the lost section of concrete suchas concrete cover over reinforcement, portiondamaged due to corrosion etc. It can be used to patchup holes in industrial floors. It is also useful inprecast concrete elements for repairing damagedpatches, corners during demoulding or duringerection.

High Performance Concrete Admixture Cum Superplasticizer For Durable Concrete/Plaster/Mortar Supercon^®-100 is a pure melamine based Superplasticizer which when added to concrete/mortar/plaster modifies the properties of concrete such as workability, strength, permeability, cohesion, etc.

• To achieve impermeable, honeycomb free, high quality concrete/mortar/plaster. (In slabs, beams, columns and areas of high steel congestion and thin sections)
• Highly recommended for Roof Slabs, Water tanks Basements, Foundations, Flooing, Bridge Decks, etc.
• To achieve pumpable concrete
• In concrete blocks & paver blocks manufacturing for impermeability & higher strength
• As a additive for internal and external plaster

Mechanism of Action:

• Pure Melamine formaldehyde resins (Supercon^®-100), when added to fresh concrete/mortar disperses cement uniformly in the mix. Due to deflocculation action on cement agglomerates, the entrapped water is released and would be available for workability. Melamine resins provide additional cohesive bond with the dispersed cement grains, thus achieving upto 25% high strength. 

SiFumex®-100-DNatural Amorphous Microsiliceous Admixture It is a well-established fact that siliceous admixture used as an essential component of concrete can impart significant enhancement to the basic properties of concrete in both the fresh and hardened state. Typical Application An admixture in high performance concretesChemical resistant concrete and mortar in Effluent and Sewerage treatment plants, Industrial floorings, Pothole repairs, Bridges, Girders, etc.Waterproofing of Water Tanks, Terraces, Basements, Walls and in all concrete structures. As waterproofing additive in brickbat cobaAddition Add SiFumex®-100-D to dry ingredients of concrete

Monobond Monobond^® is a polymer latex additive for modifying cement concrete / mortar / plaster / grouts. The addition of Monobond^® improves mechanical properties especially flexure and tension. Due to low permeability of polymer modified systems, remarkable improvement in prevention of carbonation, chloride ion penetration is observed. Also chemical resistance improves significantly. The addition of Monobond^® imparts resilience to the cement matrix. Thereby improving impact resistance. Also the modified cement matrix cures in air, eliminating the necessity of wet curing. It is necessary to mix Monobond^® in water first prior to addition in cement mortar I concrete. Application Procedure

• Mix Monobond^® in water first prior to addition in cement mortar / concrete. Dosage 10% to 15% by weight of cement.

 

SUPERCON 300Superplasticizer for High Workability & Slump Retention SUPERCON^®-300 is a superplasticizer, which when added to concrete offers the following advantages.

• Increased workability or reduction in water to cement ratio for durable and cohesive concrete
• Increase of early and final strength
• Retains slump for placing & pumping of concrete

Typical Application:

• To achieve flowing concrete
• To achieve higher workability
• Good slump retention

Mixing:

• Add SUPERCON^®-300 to concrete mix after dispersing in water

EPCO KP 100
Concrete Penetrating Corrosion Inhibitor (CPCI)^® EPCO-KP-100 is a hi-tech corrosion inhibition system that works on the Bipolar Inhibition Mechanism (B.I.M.). B.I.M. inhibits corrosion of the steel in concrete at the poles, cathodic & anodic simultaneously. EPCO-KP-100 by virtue of its high vapour pressure & affinity for the embedded metal diffuses through the densest concrete to reach the corroding steel. Upon deposition on the rusted steel substrate, EPCO-KP-100 molecules prevent further reaction between the steel and chloride/oxygen thus arresting the corrosion process. Application Procedure

• Thoroughly remove the spalled concrete and loose material. Abrade / clean the rusted steel mechanically. Spray EPCO-KP-100 along the exposed concrete surface in the vicinity
• After few minutes wipe the concrete/steel surface with moist cloth to remove residual material from the surface. The inhibitor by now has already penetrated the concrete. Follow up with application of bond coat and subsequently with repair mortar / concrete / plaster
• In case of application for preventive maintenance, abrade the concrete surface mechanically to remove loose particles, incrustations, residual oil, grease etc. Remove existing paint if the surface is already painted, by abrading
• Spray EPCO-KP-100 over entire concrete surface.
• Keep the container tightly closed in a cool place. Wear safety goggles during spraying

Dosage Rate: 4 sq.mt./lt. Spray repeatedly over the area as to dose the required quantity. Dense concrete may require repeated application, while porous substrate would absorb immediately.  

EPIBOND-21-LPBonding Agent with long pot life EPIBOND-21-LP is used to bond fresh concrete to concrete that is fully cured. EPIBOND-21-LP will give monolithic bond capable of transmitting high stresses. In addition, EPIBOND-21-LP possesses excellent water and alkali resistance and has long tackfree time of 120 minutes. This would help in laying concrete/mortar even after 120 minutes of application of bond layer. Application Procedure

• To obtain good adhesion it is necessary to have a clean and sound substrate, which can be obtained by grinding, wire brushing, chipping, sandblasting, etc.
• Mix EPIBOND-21-LP thoroughly in the prescribed proportion and apply on the clean and sound substrate
• Apply concrete / cement plaster / gunite on the tacky EPIBOND-21-LP layer which would be achieved approximately after 30 minutes of application and within two hours
• Best results are obtained when w/c ratio of the new concrete is as low as practicable

EPCO^®KP-350 + EPCO^®HP-350 epoxy mortar is a three-component system with non-shrink and high mechanical strength properties. Application Procedure

• Mix Part A(EPCO^®KP-350) and Part B (EPCO^®HP-350) in the ratio of 2:1 by weight in a clean plastic container
• Stir thoroughly for 5-10 minutes so as to achieve a uniform mix
• Add component C-Graded Quartz filler slowly and mix thoroughly to achieve a uniform mortar mix
• The mortar (A+B+C) after mixing shall be used within 30 minutes hence it is ideal for mixing small quantity at a time
• Before application of mortar the surface to be primed with bond coat of KP-350:HP-350 neat epoxy coating (Part A:Part B in 2:1 by weight)
• It is important to clean, degrease and abrade the substrate thoroughly before applying the bond coat using mechanical wire brushes

Molith MC SILVER
Free flow, shrinkage compensated, high strength microconcrete Molith^® MC SILVER is a free flow, shrinkage compensated, single component micro concrete used in high volume repairs of concrete structures. Application Methodology:

• All areas of application shall be free from oily residues, dust and loose particles
• Corroded reinforcement shall be cleaned thoroughly and treated with anti-corrosive coating Feovert^® & IPNet^®-RB
• The substrate to be treated shall be wetted with clean water (Saturated surface dry condition) prior to placement

Mixing:

• Use 25kgs of Molith^® MC SILVER bags once opened. Pour mixing water gradually into Molith^® MC SILVER in a standard mixer until required consistency is achieved. Using planetary mixer is desired for optimum performance. For 25kgs mix water requirement will be typically 3.0 to 4.0 ltrs. For larger volumes use concrete mixer 

MONOPOL 250 H
MONOPOL 250 H® is a low viscosity high molecular weight thermosett polymer. Due to its low viscosity, cracks and honeycombs in concrete are filled upto full depth of concrete.TYPICAL APPLICATIONS• For strengthening honeycombed 

EPCO-1010 Non Shrinking Epoxy Sealant
EPCO-1010® is a unique epoxy compoundcomprising of Base and Curing Agent and shouldbe mixed in equal proportion prior to use.It can be applied on concrete surface withoutaccommodating for joints as the material dose notshrink. It has built in resilience to absorb impactand movements in joints.

EL-Monobond^®-200 is a two component non re-emulsifiable high molecular weight epoxy latex system conforming to ASTM standards. Application Procedure

• EL–Monobond^®-200 is mixed first under stirrer in the prescribed proportion and diluted with approximately 50% water of the total mix (refer technical data). It is then slowly added to the (cement + sand + 50% water) mix. Planetary or suitable mixers shall be used for efficient mixing

ZEROKORR Self Healing Anti-Corrosive Coating System for Steel ( Redox Mechanism)