Good Morning Paints Private Limited

Sigmashield glass flake reinforced polyamine adduct epoxy coating
Two-component, high solids glass flake reinforced polyamine adduct epoxy coating
PRINCIPAL CHARACTERISTICS• Excellent abrasion and impact resistance• Suitable for use on ice-going vessels• Excellent resistance to corrosion• Long-term protection at areas subject to heavy wear and tear• Resistant to splash and spillage of a wide range of chemicals• Very low water permeability, due to glass flake barrier

SIGMASHIELD™ 880 GF / AMERLOCK™ 880 GF
Two-component, surface tolerant high solid glass flake epoxy coating
PRINCIPAL CHARACTERISTICS• Primarily designed for use in offshore splash zone maintenance• Designed for use in heavy-duty and corrosive environments• Outstanding sea water resistance• Excellent corrosion resistance• Enhanced impact and abrasion resistance• Continues to cure when immersed in water• Long-term protection in a single-coat application• Resistant to well designed cathodic protection• Suitable for application on exterior of buried pipes• Suitable on wet blast or ultra high pressure water (UHPWW) cleaned substrates (damp or dry)COLOR

APCODUR MIO 410 HS / APCODUR 410
Two components, high build, high solid epoxy polyamide composition pigmented with lamellarmicaceous iron oxide

PPG SIGMAGUARD CSF 585 Two-component, solvent-free, amine-cured epoxy coating
PRINCIPAL CHARACTERISTICS• Tank coating for drinking water• Can be applied by single-feed, airless spray equipment• Reduced explosion risk and fire hazard• Good visibility in confined spaces due to light color• Approved for drinking water by: KIWA The Netherlands• Meets NSF/ANSI/CAN Standard 61 for potable water when applied and used as described on

Two component, aliphatic polyurethane coating
FEATURES & RECOMMENDED USE • Designed as a finish coat in epoxy/ polyurethane systems • Good resistance to atmospheric exposure • Good gloss and colour retention • Good mechanical properties • Good aged re-coatability • Easy application by brush and spray

HEAT RESISTING SILICONE ALUMINIUM PAINT
Single pack, silicone resin based, heat resisting aluminium coating

SIGMATHERM 500 Heat-resistant up to 500C
Heat resistant modified alkyd aluminium coating
PRINCIPAL CHARACTERISTICS• To be used for the internal and external protection of steel surfaces• Heat-resistant up to 500°C (930°F); a minimum of 200°C (390°F) is necessary to fuse the aluminum coating• A minimum drying time of 3 days at 20°C (68°F) should be allowed before exposure to heat• Application by spray improves the appearance

SIGMATHERM 540 heat resistance up to 600C
One-component, heat-resistant, moisture-curing silicone aluminum
PRINCIPAL CHARACTERISTICS• Dry heat resistance up to 600°C (1112°F)• No heat cure necessary between coats• To be used for the internal and external protection of steel surfaces• Excellent resistance against weathering• Also suitable on top of zinc silicate primer• A minimum drying time of 3 days at 20°C (68°F) should be allowed before exposure to heat

APCOTHERM HR 600 ALUMINIUM 
Single pack, silicone resin based, heat resisting aluminium coating
FEATURES & RECOMMENDED USE• Dry heat resistant up to 600°C• Good water & weather resistance• Can be directly applied over zinc metallised substrate or zinc silicate primer

APCOTHANE CF 672 HS / APCOTHANE 672
Two component high solid, low VOC acrylic aliphatic glossy polyurethane coating
FEATURES & RECOMMENDED USE• Designed as a finish coat in epoxy/ polyurethane systems• VOC compliance and high solids• Excellent resistance to atmospheric exposure conditions• Good resistance to water and saline atmosphere• Provides tough, abrasion resistant finish with excellent colour & gloss retention

APCOTHANE CF 676 ALUMINIUM PAINT Three component, aliphatic polyurethane aluminium coating
FEATURES & RECOMMENDED USE• Designed as a top coat for industrially polluted environments• Good water resistance• Good weather resistance

APCOSIL 605 IZSS
Two component, moisture curing inorganic zinc silicate coating
– Designed as an anticorrosive primer for application in aggressive – Good resistance to saline and marine atmosphereenvironments – Can withstand substrate temperatures ranging from -90o C to +600o C– Excellent solvent resistance

Two component, polyamide cured epoxy zinc rich primer

Two components, high build, epoxy coating for containment and reactor building

APCOFLOR HFP 130 Self Levelling Epoxy Flooring Primer
Two component, high solid, epoxy resin based floor primer.
FEATURESTECHNICAL DATASUBSTRATE QUALITY• High performance phenlkamine based epoxy primer.• Designed as a high solid primer for concrete surface.• Primer for APCOFLOR flooring systems.• Provides good adhesion between concrete surface and subsequent APCOFLOR topcoat.• Good penetrating and sealing properties.• Good bonding with sound old and new concrete surfaces.• Excellent bond strength.

Two component, high build coal tar epoxy coatingFEATURES & RECOMMENDED USE• Good resistance to corrosion in marine exposure and subsoil conditions• Good abrasion resistance• Good chemical resistance• Excellent water resistance

APCOSIL 605
A two component solvent based moisture curing inorganic zinc silicate coating
FEATURES & RECOMMENDED USE• Heavy duty primer, offering excellent corrosion protection in highly aggressive environments for steel structures• Excellent resistance to saline and marine / offshore atmosphere• Recommended system primers in various high performance systems based on unsaponifiable binders• Excellent water and solvent resistance• Can withstand substrate temperatures from -90°C to +400°C, under normal atmospheric exposure conditions• With suitable top coat, provides excellent corrosion protection for steel substrate up to +600°CTECHNICAL DATAColourGreyGlossMattRecommended DFT / Coat50 - 75 μmTheoretical Coverage Capacity13.2 sq.mtr/l @ 50 μm DFT8.8 sq.mtr/l @ 75 μm DFTDrying time at 30°CSurface dry : 30 minutesHard dry : 8 hoursFull cure : 7 daysOver coating interval at 30°CMin. : 8 hoursMax. : Unlimited (provided surface is free from any contamination)Method of ApplicationAir spray & Airless sprayThe data given is for guideline only. The physical values are subject to normal manufacturing tolerances, colour and testing variancesThe actual drying time/ overcoat interval may be shorter or longer, depending on film thickness, ventilation, humidity, temperature etc.The information provided above is at 30 °C and 65 % relative humidityDIRECTIONS FOR USESurface PreparationGeneral

Single pack, air drying, high gloss alkyd finishing paint. We are engaged in offering Quality Products to our clients. Our range of all products is widely appreciated by our clients.

Single pack, air drying, alkyd based composition with zinc chrome pigment– Anti-corrosive primer for conventional system
– Can be top-coated with conventional or chlorinated rubber coatings
– Easy application by brush and conventional spray

Two components, high solid, high build zinc phosphate based epoxy primer cum finish. We are engaged in offering Quality Products to our clients. Our range of all products is widely appreciated by our clients.

Two component, acrylic aliphatic polyurethane coating. We are engaged in offering Quality Products to our clients. Our range of all products is widely appreciated by our clients.

APCOTHANE HB PU FINISH / APCOTHANE 680
Two component high build, high solid, acrylic aliphatic polyurethane coating
FEATURES AND RECOMMENDED USE• Finish coat in epoxy / polyurethane systems• Good resistance to atmospheric exposure• Good resistance to water and saline atmosphere• Gives tough, abrasion resistant finish on curing

APCOGLASS MASTIC 2000 / APCOGLASS 2000 Glass Flake
Two component, high built, high solids, glass flake reinforced polyamine cured epoxy surface tolerant coating
FEATURES & RECOMMENDED USE• High performance coating for highly aggressive aqueous/ chemical environment• Excellent corrosion and chemical resistance• Excellent impact and abrasion resistance• Compatible with various aged sound oleoresinous, epoxy and polyurethane coatings• Self-priming coating, tolerant to lower grades of surface preparation• Very low water permeability, due to glass flake barrier• Low volatile organic content

APCODUR ZINC PHOSPHATE PRIMER /APCODUR 206
Two component, epoxy primer with zinc phosphate pigment
FEATURES & RECOMMENDED USE• Designed as an epoxy primer with good resistance to saline, marine and chemical environment• Free from lead and chromate containing pigment• Good adhesion on steel• Can be over coated with alkyd, chlorinated rubber, acrylic, epoxy, polyurethane coating

APCOGUARD SF 725
Two component solvent free epoxy phenolic tank lining
FEATURES AND RECOMMENDED USE
• Designed as a chemically resistant heavy duty tank lining to provide corrosion protection to the internals
of steel storage tanks
• Excellent resistance to crude oil, lubricating/ furnace oils, alcohols, aromatic/ aliphatic solvents, gasoline
blends, gasohol and refined petroleum products like petrol, diesel, kerosene, aviation fuel, MTO etc.
• Excellent water resistance
• Self-Priming having excellent adhesion on blasted steel
• Certified to overall migration standard as per 21 CFR 175-300 of US –FDA by CFTRI India for potable
water
• Very low VOC which eliminates the fire risk when applied in the confined area

APCOSIL 605 85% / APCOSIL 615
A two component solvent based moisture curing inorganic zinc silicate coating, containing 85% zinc by weight in the dry film. Complies with zinc dust level classification as per SSPC Paint 20 level 1Available in zinc dust levels as per ASTM D 520, Type II
FEATURES & RECOMMENDED USE• Heavy duty primer offering excellent corrosion protection in highly aggressive environments for steel structures• Excellent resistance to saline and marine / offshore atmosphere• Recommended system primers in various high performance systems based on unsaponifiable binders• Excellent water and solvent resistance• Can withstand substrate temperatures from -90°C to +400°C, under normal atmospheric exposure conditions• With suitable top coat, provides excellent corrosion protection for steel substrate upto +600°C

APCOTHERM HR 600 / APCOTHERM 600
Single pack, silicone resin based, heat resisting aluminium coating

APCOTHANE WB 200
Single pack, fast drying, hygienic, water based polyurethane dispersion wall finish
FEATURES• Single pack, water based VOC compliant wall coating• Hygiene wall coating• Excellent anti-microbial anti-fungal performance• Suitable for both interior and exterior application• Excellent scrub resistance• Excellent resistance to stains and chemicals• Odour free and easy to apply• Easy to clean and maintain• APCOLITE universal stainer can be used for minor shade alterations• Finds application in sterile & clean rooms in pharmaceutical units, hospitals, food processing units, construction requiring quick turn-around etc.

Single pack, air drying, oleoresinous composition with zinc chrome & red oxide pigments

Two components, high build, high solid, zinc phosphate based acrylic aliphatic polyurethane direct to metal coating

Two component, high build, self-priming, rust encapsulating, modified epoxy coating

A Two-pack, air drying etch primer based on zinc tetroxy chromate and polyvinyl butyral

APCODUR MIO / APCODUR 415
Two components, high build, high solid, micaceous iron oxide pigmented epoxy coating
FEATURES & RECOMMENDED USE• Designed as an epoxy intermediate in protective coating systems for steel and concrete structures exposed to aggressive conditions• Excellent resistance to moisture and saline conditions• Good resistance to water and to splashes of mild chemicals• Good abrasion resistance

APCOSIL 605 IZ Inorganic zinc rich silicate
A two component solvent based moisture curing inorganic zinc ethyl silicate coating
Features and Recommended use• Designed as primer coat for application in highly aggressive environments• Excellent solvent resistance• Good resistance to saline and marine atmosphere• Can withstand substrate temperatures ranging from -90°C to +600°C• Not suitable for immersion in alkaline (more than pH 9 ) or acidic ( less than pH 5 ) liquids without suitable topcoats

APCOSIL 605 Z85  APCOSIL 610 Inorganic Zinc Silicate
Two component solvent based moisture curing inorganic zinc ethyl silicate coating
• Heavy duty primer, offering excellent corrosion protection in highly aggressive environments for steel structures• Meets zinc dust classification as per SSPC Paint 20 level 1• Good resistance to and marine / offshore atmosphere• Recommended system primers in various high performance systems based on unsaponifiable binders• Excellent water and solvent resistance• Can withstand substrate temperatures from -90°C to 400°C, under normal atmospheric exposure conditions• With suitable top coat, provides excellent corrosion protection for steel substrate up to 600°C

APCOSIL 605 – ZS
A two component solvent based moisture curing inorganic zinc ethyl silicate coating
FEATURES AND RECOMMENDED USE• Heavy duty primer, offering excellent corrosion protection in highly aggressive environments for steel structures• Excellent resistance to saline and marine / offshore atmosphere• Recommended system primers in various high performance systems based on unsaponifiable binders• Excellent water and solvent resistance• Can withstand substrate temperatures from -90ºC to +400ºC, under normal atmospheric exposure conditions• With suitable top coat, provides excellent corrosion protection for steel substrate up to +600ºC

Single pack, air drying, general purpose, glossy DTM Enamel. We are engaged in offering Quality Products to our clients. Our range of all products is widely appreciated by our clients.

Single pack, air drying, high gloss alkyd finish paint. We are engaged in offering Quality Products to our clients. Our range of all products is widely appreciated by our clients.

Two components, high build, polyamide cured epoxy coating. We are engaged in offering Quality Products to our clients. Our range of all products is widely appreciated by our clients.

Two component high build, high solid, acrylic aliphatic polyurethane coating. We are engaged in offering Quality Products to our clients. Our range of all products is widely appreciated by our clients.